Applying more pressure increases the stroke speed. After working for longer periods at low stroke rate, allow the machine to cool down by running it at maximum stroke rate and no-load for approx. Contact Protector The contact protector 12 attached to the housing prevents unintentional contact with the saw blade while working and should not be removed.
Sawdust Blower The sawdust blower leads an air jet to the saw blade. The air jet keeps sawdust from covering the cutting line during operation. Sawdust blowing level II: Medium airstream, for cuts in materials with low chip removal rate, e. Sawdust blowing level III: High airstream, for cuts in materials with high chip removal rate, e. Pendulum Action Setting The four pendulum action settings allow optimum adaptation of cutting speed, cutting capacity and cutting pattern to the material being sawed.
The pendulum action can be adjusted in four steps with the adjustment lever 7. Switching is possible with the machine running: Step 0: No pendulum action Step I: Low pendulum action Step II: Medium pendulum action Step III: High pendulum action Recommendations: — The more narrow and clean the cutting edge should be, the lower the pendulum action level should be selected or switched off. The optimal setting can be determined by practical testing.
After coarse adjustment, tighten the screw 14 so that the base plate 8 can still just be adjusted. The cutting angle can be pre-adjusted by means of the scale for mitre angles Precise adjustment with use of a commercial angle gauge 15 is recommended.
Then tighten the screw 14 again. For this, however, the base plate must be pushed back towards the motor to the stop, so that the notch in the base plate engages in the positioning pin Offsetting the Base Plate see figure B For sawing close to edges, the base plate can be offset to the rear: Use Allen key 5 to take out screw 14 completely. Lift the base plate and move it to the rear such that the screw can be turned into the rear thread. When tightening the screw 14, the base plate must be pressed to the rear until it can be felt to engage.
Splinter Guard see figure C To avoid fraying of the surface, install the splinter guard 18 by pressing it into the base plate 8. The splinter guard cannot be used for certain saw blade types e. For tight curves it is best to use a narrow saw blade. Plunge Cutting see figures F — G Plunge cuts may only be applied to soft materials, such as wood, aerated concrete, gypsum plaster boards, etc.! Place the machine with the front edge of the base plate on to the workpiece and switch on.
Firmly hold the machine against the workpiece and by tilting the machine, slowly plunge the saw blade into the workpiece. When the base plate fully lays on the surface, continue sawing along the cutting line. In extreme working conditions, conductive dust can accumulate in the interior of the machine when working with metal. The protective insulation of the machine can be degraded. The use of a stationary extraction system is recommended in such cases as well as frequently blowing out the ventilation slots and installing a residual current device RCD.
If it is worn, it must be replaced. If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an authorized after-sales service agent for Bosch power tools. In all correspondence and spare parts orders, please always include the digit article number given on the nameplate of the machine. Important instructions for connecting a new 3-pin plug to the 2-wire cable. Important: If for any reason the moulded plug is removed from the cable of this machine, it must be disposed of safely.
Disposal To be fitted by qualified professional only Power tools, accessories and packaging should be sorted for environmental-friendly recycling. Typically the A-weighted sound pressure level of the machine is 83 dB A. When working, the noise level can exceed 85 dB A.
Wear hearing protection! WARNING The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN and may be used to compare one tool with another.
The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the level given in this information sheet.
This could lead to a significant underestimate of exposure when the tool is used regularly in such a way. NOTE: To be accurate, an estimation of the level of exposure to vibration experienced during a given period of work should also take into account the times when the tool is switched off and when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Click to see full answer. Besides, how do you remove the blade from a Bosch jigsaw?
Push the blade change button down with your thumb and turn the forward handle counterclockwise three complete times. Grasp the blade by its sides with your fingers and push the blade up to release the tabs on the blade from the plunger. Furthermore, how do you remove a stuck Sawzall blade?
Grasp the blade with a pair of pliers in your free hand. Pull the blade straight out of the Sawzall Hatchet. Jiggle the blade up and down with the pliers if necessary until the blade comes out of the saw.
Release the collar once you remove the blade. Put your finger beneath the lever that releases the blade and lift. Shake the DeWalt jigsaw gently.
Make sure you have the proper blade when changing a DeWalt jigsaw blade. Additional data Rated input power W Stroke rate at no load — 3, spm Weight 2. Need a spare part? Find the right spare part. Part number EC. Description Jigsaw. Yes, the part number matches. I'm looking for a spare part for this product. Go to spare part. The declared vibration emission level repre- sents the main applications of the tool.
However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may signifi- cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibra- tion should also take into account the times when the tool is switched off or when it is run- ning but not actually doing the job. This may sig- nificantly reduce the exposure level over the to- tal working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.
Stroke rate control — z Rated power input W Output power W Stroke rate at no load n0 min-1 — Stroke mm 26 26 Cutting capacity, max. For lower voltage and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary. Page: 9 20 English 1 S92 6.
Danger of injury when touching the saw blade. Selecting a Saw Blade An overview of recommended saw blades can be found at the end of these instructions. Use only T-shank saw blades. The saw blade should not be longer than required for the intended cut. Use a thin saw blade for narrow curve cuts. A loose saw blade can fall out and lead to inju- ries. For removal of the saw blade, proceed in re- verse order. Splinter Guard see figure B The splinter guard 14 accessory can prevent fraying of the surface while sawing wood.
When sawing with the splinter guard, the base plate 8 must not be moved back for cuts that are close to the edge. Press the splinter guard 14 from the bottom into the base plate 8. Certain dusts, such as oak or beech dust, are considered as carcinogenic, especially in connection with wood-treatment additives chromate, wood preservative. Materials containing asbestos may only be worked by specialists. Pull the saw blade 10 a little downward until it engages.
While inserting the saw blade, pay attention that the back of the saw blade is positioned in the groove of the guide roller 9. Continue turning the rotating handle 1 to the starting position and then push it all the way down. Observe the relevant regulations in your country for the materials to be worked. Operation Operating Modes f Before any work on the machine itself, pull the mains plug. Orbital Action Settings The four orbital action settings allow for optimal adaptation of cutting speed, cutting capacity and cutting pattern to the material being sawed.
The orbital action can be adjusted with the ad- justing lever 7, even during operation. The optimal orbital action setting for the respec- tive application can be determined through practical testing. The following recommenda- tions apply: — Select a lower orbital action setting or switch it off for a finer and cleaner cutting edge. Loosen the screw 16 and lightly slide the base plate 8 in the direction of the saw blade Swivel the base plate 8 to the desired position according to the scale Other mitre angles can be adjusted using a pro- tractor.
Afterwards, push the base plate 8 to the stop to- ward the mains cable. Tighten the screw 16 again. The splinter guard 14 can not be inserted for mi- tre cuts. Offsetting the Base Plate see figure D For sawing close to edges, the base plate 8 can be offset to the rear. Completely unscrew the screw 16 using the Al- len key 5. Take the base plate 8 off and remount it offset again so that the screw 16 can be screwed into the rear bolt hole Now, tighten the screw 16 again.
In addition, the parallel guide with circle cutter 21 accessory as well as the splinter guard 14 may not be used.
0コメント